Skip to content
The Vaughn Velocity V10 Pro Carbon Senior Goalie Leg Pads are constructed with a firm internal core accompanied by HD side rails, ensuring enhanced stability. An inner pad edge equipped with quick-slide material aids in swift movements, and the easy flex lower scoop design contributes to agility. The integration of a knee landing pad connected to the inner core results in immediate pad response. Extended back leg coverage, a lower profile outside roll with a single break style, and a plus 2" thigh-rise with a square-shaped inside edge further enhance functionality.
The outer panel maintains a thinner profile to reduce bulk, and the pads come pre-curved for precision. They are equipped with a two-way adjustable knee cradle strap, a knee cradle center for rapid pad rotation and control, and a wider inner knee landing surface. The pad design incorporates three flat knee rolls and Pro-spec domestic construction, utilizing an inner foam core with a carbon surface reinforcement for added durability. The pad shape maximizes its full 11" width from top to bottom, and the outer knee cradle pad is both adjustable and removable. Lastly, the reinforced instep with a flat profile facilitates skate movement during pad rotation.
Vaughn Velocity Senior Leg Pad Sizing Chart
Leg Pad Size Floor-to-Knee Measurement
32” 19.5 – 20.5" 49.7 – 52.3 cm
33” 20.5 – 21.5" 52.3 – 54.8 cm
34” 21.5 – 22.5" 54.8 – 57.4 cm
35” 22.5 – 23.5" 57.4 – 60.0 cm
36” 23.5 – 24.5" 60.0 – 62.2 cm
Goalie Leg Pads Sizing
Deciding your Goalie Pads size is crucial for having total control while moving in the crease. Sizing your pads properly is the difference between getting that perfect seal on your butterfly, and feeling clunky or unprotected in the net. Below we have compiled some information to better assist you in deciding which size is right for you.
Floor-To-Knee Measurement
Your Floor-To-Knee measurement will give you a good indication as to what "Pad Size" you will need. This measurement can be matched up with the provided sizing chart above.
How to Measure your Floor-To-Knee
1. In your bare feet, place the soft measuring tape at the inside of the bottom of your foot.
2. Slightly bend your knee.
3. Run the soft measuring tape up your shin, to the middle of your knee.
4. Match your Floor-To-Knee measurement with the provided sizing chart
What to look for when trying on your new pads.
Once you have your new leg pads, you’ll need to make sure they fit you properly. To do so, you’ll need to put the pads on with your skates. There a couple things to do to check size, once you have the pads on:
1. Stand straight and bring your feet together. This will show you the overall height of the pad, while on. Your pads should not be taller than your hips. Ideally you want the top of your pad at the half-way point of your thighs. A pad fitted for a young growing goaltender can be a little taller, so a little above the half-way point is normal.
2. Next you want to get in your stance, keep your hands in a ready position, and drop to your butterfly. Without moving your legs to correct your butterfly, bring your heels together. This is where you assess your knee position. For a proper fit, you want the middle of your knee to sit directly on the center of the knee stack. If you’re looking for growing room, you want the middle of your knee to land roughly 1.5” below the center of the knee stack (1” for JR).
Not getting a complete seal while in your butterfly?
If you're having trouble getting a full seal in your new pads, it may be the way you’re strapping them up. Make sure your boot strap and top straps (above knee) are loosened up a bit. The reason you want these straps loose is because they have a direct effect on the rotation of the pad. Having a loose boot strap makes it easy for your foot and ankle to rotate as the pad moves. Same goes for the top straps, as you don't want them pulling down too hard on the thigh rise.